A bit more INNOVV-ation!

All I can say is – WOW! Since the link was added to the INNOVV website about the K1 review, I don’t think I’ve ever had so much traffic or comments in one day. Absolutely fantastic and wonderful to swap emails with so many other riders!!

Aprilia Caponord ETV1000 Rally-Raid ferrite clip-on core for INNOVV K1So as a follow on, today I’ll answer a couple of questions that folks have raised. Firstly, ferrite cores, what are they and what do they do. In a nutshell wires can act as aerials, bringing unwanted high-frequency signals into (or out of) an electrical circuit, such that this interference causes problems. By fitting  a clip-on ferrite core you prevent these unwanted signals from entering or leaving – in this case the DV recording unit. In my case for example, when I tapped the horn button (Stebel Nautilus Compact Tuning – 18A!) the DV recorder would always reboot itself. Since fitting the ferrites – no problems at all when using the horn! The ferrites I bought are for 3.5mm cable and fit all the INNOVV wiring just fine.

Aprilia Caponord ETV1000 Rally-Raid INNOVV button & LED schematicSecondly, the button/LED replacement I made. Here’s a breakdown of the existing button – just a momentary push-to-make switch and a red LED, nothing more. As mentioned in the previous post, the voltage to the switch is 3.8v and to the LED 1.8v pulling approx. 11ma. The switch could easily be replaced by any momentary switch you like, that’s easy, unfortunately though the LED is drawing very little current and so this line cannot be relied on (without frying something!) to power a brighter LED that would typically draw around 20-30ma, so a new circuit is required. Now this could be as simple as using this line to drive a transistor such as in the diagram below. Here a fused switched 12v line provides the required Aprilia Caponord ETV1000 Rally-Raid INNOVV K1 new LED driver circuitvoltage/current  to drive an LED via a transistor. In this case the INNOVV provides the 1.8v (at 0.5ma) to switch the transistor. This circuit could all be assembled inline with the LED to save space …… however it would have to be meticulously assembled, if the 12v line touches the 1.8v line, then goodnight DV recorder!! Much better to buy a small box and a piece of strip-board from Maplin (UK) or RadioShack (USA)  and build the circuit into the cable run.

Remember that if you want to use a green or blue LED instead of the red one, then the 560Ω resistor will need to be replaced with a 510Ω one to compensate for the different voltage requirement.

Now this where I admit I didn’t do it this way! That’s because I wanted to add a couple of other functions that I thought were useful, so I went and added a microcontroller into the melting pot. On the standard setup, when the button is pushed (long) the recorder starts or stops and the LED changes state – in other words, I have feedback from the unit while I’m riding along. However when the button is pushed (momentary) the LED does nothing …. the DV unit will say “Video file protected” and the red dot on the recorder screen will change to a yellow triangle with an exclamation mark in it, but I can neither hear or see any of this from the saddle. So for file protect/unprotect I don’t have any usable feedback and I wanted to change that.

Now the microcontroller runs a combined red/green LED – this lights green when recording and off when not recording, if file protect is enabled then it toggles red/green for 0.5 seconds at 10Hz then turns red denoting that the file currently recording is now protected. Another push of the button reverses the process – red/green toggle and then solid green for unprotected file recording.

Aprilia ETV1000 Caponord Rally-Raid LED dashboard cockpit Garmin Zumo 590LM

There is also one other feature ……. when file protection is enabled, it is ONLY for the current file. So if for example you activate file protection with a 10 minute file at 9 minutes 58 seconds elapsed, then 2 seconds later a new file will begin to record and it is UNPROTECTED, see the issue? So now, if I have activated file protection, the microcontroller waits until the new file begins recording and triggers file protection itself in the background and will continue to do so until I deactivate it. All the time I know I’m recording a sequence of protected files because the LED is red not green.

 

INNOVV K1 Dual Camera system – Review at 6 months

Aprilia Caponord ETV1000 Rally-Raid INNOVV K1 dual HD camera systemI joined the HD camera bandwagon back in January 2014 and since then have enjoyed (or not!) the delights and foibles of the GoPro Hero 3+ Black camera. Constantly charging a bucket load of batteries, taking it on and off the bike then getting frustrated when the current battery needs replacing/recharging in oh-so short a time.

In the end of course the penny dropped. The GoPro is simply overkill for day-to-day riding where (hopefully) nothing of any note happens. But if it did, I’d still like to capture it if possible, just in case it could help with an insurance claim or legal dispute.Aprilia Caponord ETV1000 INNOVV K1 DVR & GoPro 3+ Black

I realised that what I wanted wasn’t an ‘Action camera’, but a ‘dashcam‘ …. a subtle difference it seems! So here’s what I’d like it to do:-

  • Bike AND battery powered – turn on/off and record video with just the turn of the ignition key
  • 2 cameras – forward and rear both recorded by a single unit
  • Full HD – 1920 x 1080 (30fps minimum) progressive with good low-light capability
  • Protect files – Either on demand or on collision detection
  • Be designed for motorcycles – waterproof and ruggedised.

And so courtesy of Jim at Abbey Motorcycle Instructors in Oxfordshire, an INNOVV K1 dual-camera kit found its way to the Capo. While the INNOVV didn’t tick all of my ‘wish-list’ it ticked more than most. The full specification of the K1 can be viewed here.

I’ll skip ‘what’s in the box’ and unpacking waffle because all this is available on the INNOVV website, along with quick-install instructions and owners manual. What I ended up with is the motorcycle kit (including the 12v/5v voltage regulator*) and a 128Gb memory card. The owner’s manual specifies 64Gb max but INNOVV sell the 128Gb, so I can only assume the manual hasn’t been updated yet following firmware updates.

To fit the kit to the Capo required a bit of sacrifice. The long serving and ultra-reliable Autocom Pro-7 unit had to come off the bike and has now been streamlined and put into the tank bag along with the ICOM PMR446 radio. You really can’t keep a good, but very old bit of kit down for long!

Installation

Aprilia Caponord ETV1000 Rally-Raid INNOVV K1 rear camera mounting pointThe INNOVV 12v/5v voltage regulator is wired into the tail-light loom and installed on top of the ECU with a (provided) double-sided sticky pad. I have to be honest here and admit that I already have an extra loom in place ready for the Active Brake Light System which is still being built. So in the meantime I pinched its Molex connector to power the K1. Next the GPS unit was installed in the Capo’s luggage bay just behind the ECU on a 3D printed bracket so it fits nicely next to the MCCruise electric servo.

With that done it was time to install the cameras. I decided I wanted them on the center-line of the bike rather than bias them one side or the other. I wanted them EU/UK road friendly! The rear is mounted just above the tail-light and the front on the headlight guard. Both are angled down about 7º to reduce glare, each has an excellent view of the road with only the edge of the top-box getting in the rear camera frame. The cameras are each physically identical (just different cable length) and have machined aluminium bodies that are waterproof and heavy-duty, however the lens (especially front) Aprilia Caponord ETV1000 Rally-Raid INNOVV K1 camera system 3D printed front mountis vulnerable and would benefit from some protection. They each have three 1/4-20 UNC thread mounting points (normal camera thread) and come with basic steel L-brackets. However I decided to make my own to best suit the mounting points – the rear from a piece of steel plate, while the front is 3D printed and bolts to the headlight guard (AP8791235). The final two items in the box are the push-button and a small loom that plugs into the DV recoreder, joining both button and GPS USB’s to one connector,  however I left this off for the initial trials – more about this later.

Setup

With the kit fitted it was time to set-up the unit in the two recorder menu’s. Time, date and vehicle name are straight forward as was selecting camera orientation – one of mine had to be rotated. Initially I set both cameras to 1920×1080, then had a play with 1280×720 on the rear, but ultimately went back to full HD on both. Again all the settings (bar one) are covered in Aprilia Caponord ETV1000 Rally-Raid INNOVV K1 DVR dual camera HDthe manual. The one that is missing is ‘EDOG beep’ …….. INNOVV tell me this is to do with warning of being over-speed but requires the speed camera data to be installed. Besides, the ‘beep’ is under the saddle and inaudible for riders, so I leave it switched off.

The system also incorporates accelerometers in the front camera and they can be used to lock video files or start the cameras (Park Mode) when they detect an impact above a certain value. Setting this value  is trial and error and at first I found it locked files when riding along our dirt/stone road. It’s something you can tweak over a few rides until it suits your roads/riding style I guess.

Operation and observations

With the Capo buttoned up, it was time to give it a whirl and see if it really is as fit-and-forget as I wanted. In short yes it is! We all have our little routines and mine is key-on, wait for the dashboard to finish its self-test, hit the starter and when the motor settles, turn on the lights. At that point the K1 turns on and immediately begins recording. I set mine for 10 minute segments, the selection is 1, 2, 5 and 10 minutes. At the end of the ride simply shut off the lights or ignition and the K1 reverts to its internal 3.7v 1100mAH battery** to finish the current file and store it, then it shuts down. It couldn’t be any more turn-key if it tried! The K1 also has voice (and beep/bong!) confirmations that tells you what it’s doing, but you look mighty odd jumping off your bike and sticking your ear to the pillion saddle, so I turned it off once confident it was working reliably.

Aprilia Caponord ETV1000 Rally-Raid Datakam Windows software from INNOVV K1 SD cardWith a 128Gb card installed it records for about 14∼15 hours before overwriting the first files it recorded. All video files can be viewed directly on the recording unit, with basic fast forward/reverse functions or remove the SD card and pop it into your computer. When you format the memory card in the recorder it adds a useful viewing program (Registrator Viewer 5.8 for Windows) that allows you to not only view the files but it can also show you location/speed/heading from the GPS data and data from the accelerometers. However, if you want to save your video as picture-in-picture format like you see dotted around the internet, you’ll need a video editing package such as Adobe Premiere Elements.

What about picture quality? I left the menu settings at default, however there are a few items specifically for tweaking the image quality – resolution, quality (Normal, Fine & Super Fine) as well as WRD (Wide Dynamic Range). This improves the cameras night-time images or images with strong back-lighting where objects appear more in silhouette. Personally I find the images pretty good but a little over sharpened such that there is some noticeable image ringing. Also the data rates differ front to rear, the front camera has a data rate of 12Mbs while the rear is reduced to 8Mbs and I found definite compression artifacts on the rear footage especially (for example) when riding along a tree-lined road where the image has lots of fast changing areas (overhanging trees) instead of  a relatively constant sky. Maybe I’m being a little harsh here. After all it is a budget dual camera system not a high-end Sony/Nikon/Cannon! But having said that, and looking at the specification of the Ambarella OV2710 sensor and A7LA70 chipset I can’t help but think that image quality can be improved by tweaking the firmware. Maybe an update will be released in 2017?


Here’s a short video put together from K1 and GoPro (top left & audio) footage. The Capo popping on the overun has stopped since the new camchain tensioner was fitted and the slight front camera movement has gone since the new mount has been fitted ….. oh and some of the quality has been lost sending it over to YouTube. 🙁 I think I better do a new video!!

 


Parts not used

As mentioned previously, there is a push-button provided as well. This is used to lock/unlock (momentary push) the currently recording video file and (2-3 second push) to start or stop the recording. When recording an LED is lit in the button. Now here is Aprilia Caponord ETV1000 Rally-Raid Autocom PTT INNOVV push-button & LEDquite possibly my biggest gripe of the K1 system. The button isn’t waterproof and the LED is so weak as to be almost impossible to see except in a dimly lit room (or car interior?). I decided to strip it to find out what makes it tick, then set about replacing it with something more useful.

 The button has two functions – first it grounds a 3.8v signal line (the button push), second the LED is fed by a 1.8v 11mA signal from the DV recorder – both ground through a third wire. So I knocked up an interface box to improve the LED power and feed both signals forward to the old Autocom PTT (Push to Talk) button I still had on the handlebars. Now I have a waterproof, heavy-duty push-button and a much brighter LED that I can see in daylight.

Conclusion after 6 months use

Aprilia Caponord ETV1000 Rally-Raid INNOVV K1 dual camera DV recorder 3D printed caseOverall I’m pretty happy with the kit and enjoy letting it do its thing …. nowadays I don’t think about it and only check the cameras are clean before heading out. In fact I only checked the SD card yesterday after about a month – everything is recording just fine.

The one niggle I had early on was intermmittent locking-up or shut-down of the DV recorder. This was cured by fitting ferrite cores to all the leads. The only other change I’ve made has been the replacement of the bag provided for the DV recorder with a 3D printed frame – similar protection but with better ventilation for cooling – it does get VERY warm over time!  Anyway, here are a few more bullet points that come to mind.

Good

  • Build quality, installation instructions & general performance
  • Price (pre BREXIT £/$ crash!) of approx £200
  • Availability of accessories and spares
  • Communication with INNOVV – quick response to emails.

Could be better

  • Improve video quality – reduce compression and sharpening
  • Waterproof heavy duty button with bright LED specifically for motorcycles
  • Supply a pair of lens protectors in the kit
  • Susceptible to RF interference – shielded wires or add ferrite cores to cameras/GPS/switch wiring
  • Waterproof  cases for the GPS and DVR unit.

Other things to possibly consider for the future ….

  • Improved battery capacity and reduced drain when unit is switched off
  • Wireless or Wi-Fi capability for intercom or Off-Bike video file storage on a smartphone. Maybe the system could notify you via SMS if the Park Mode is activated by impact?
  • Combine the DVR and GPS units to reduce the overall number of cables and connections.

* The voltage regulator has been updated with a sensing wire to be attached to a switched 12v source while the red/black connect directly to battery supply. The regulator supplied in my kit did not have this upgraded function.

** This is the same battery as used in the old GoPro / GoPro2 – Battery model AHDBT-001 or 002. There are loads of aftermarket versions of these on the Ebay if you need to replace it.

Lights, camera …….. action!

Honda GL1500 with cam-cover-camera!Video on bikes ……. Nothing new of course, it’s been going on for ages. But for what it’s worth, here’s a potted history of moto-abruzzo’s fumbling’s as a videographer.

This pic is probably where it all began, back in 1992 on a hot day in Italy when I was bored. I strapped my analog camcorder to the cylinder head of the 1500 Goldwing and had a fun afternoon playing. The low perspective added drama to the shots and I could watch the front end working in corners …. Well as much as you can corner on a Goldwing! But of course the kit was bulky and not waterproof in the slightest, Sony Video Walkman GD-V800so once I’d had a play I never touched it again – especially in the rain soaked confines of the UK.

It was 2001 before I used video again. Now working as a full time Motorcycle Instructor I could see the value of using video as a training aid, so I fitted my Triumph Trophy 1200 with two 720×520 colour bullet cams (front & rear) and used a Sony Video Walkman GD-V800 deck to record. The cameras were interchangeable with PIP (Picture in Picture) so one image was primary while the other was a thumbnail in the corner. It all worked very well and I learned a great deal about camera placement, lens choice, filming and editing video from those days. Sadly, when the Trophy was written off in 2005 the video gear just sat in a corner of the workshop and never got fitted permanently again – mainly because no bike stayed long enough until I got the Caponord!

GoPro Hero 3+ BlackAnd that brings me up to date I guess. 2014, a new year and all that jazz, will see moto-abruzzo once again playing with video. Hopefully this time it will add a new perspective to the website and move things in a slightly different direction. After a few weeks of internet-homework, weighing up the pros and cons of some amazing kit, I’ve chosen the GoPro Hero 3+ Black as the camera platform to use. I’m not going to bang on about the camera as a zillion websites and YouTube videos are available to review this kit, it’s enough to say that in comparison to previous kit I’ve used it look fantastic, is a magnitude more advanced and  …….  well lets just say I can’t wait to get filming!