MOTRAG cooking set and gas burner – 2.7Kw!!!

Aprilia Caponord ETV1000 Rally-Raid Motrag pot and burnerMaybe I’m a tight git or just a fussy bugger, but when I’m on the road I like a mug of tea (or coffee) my way – not some overpriced bucket of gut-wash served up at Costa-Bucks on almost every street corner and in every motorway services. If it’s a short trip I’ll take a flask, if it’s a biggie I take a Trangia … or at least I did!

I’ve been using a Trangia for donkeys years …. they’re reasonably compact, easy to set up and heat predictably although there is a definite knack to setting the flame adjuster if you don’t want cooked fingers as well. The wind shield does a good job and the whole thing is well planted and has a low center of gravity to keep it stable – in other words well designed.

So when Manuel at Motrag asked me to try out the cooking kit and gas burner he sells through his website I must admit to not being 100% enthusiastic. I like my Trangia. Anyway since last summer I’ve used his setup and have to admit (begrudgingly! 🙂 ) it does have some distinct advantages and to be fair the shortfallings are easy to work around.

Aprilia Caponord ETV1000 Rally-Raid Motrag gas burnerThe burner is a work of art! Very small and very powerful. Back to back tests between the gas burner and the pre-heated Trangia had the 0.6L kettle boiling in 4 minutes and 8 minutes respectively, so it certainly has some punch to it and of course using a gas canister is far less messy than using Methylated spirit. The gas canister and burner pack away into the two halves of the pot kit (2x pots – 0.4L & 0.8L) and this in turn packs away into a neat bag. Overall the Motrag kit is 155mm high x 125mm diameter – approx. 1.9L volume and weighs in at approx. 540g INCLUDING a full gas canister. In contrast the Trangia 27 (2 x 1L pots, 0.6L kettle & frying pan) is 100mm high x 185mm diameter – approx. 2.7L volume and 880g in weight EXCLUDING fuel, certainly making the Motrag set more pannier/top-box friendly if space is a premium.

Aprilia Caponord ETV1000 Rally-Raid Motrag gas burner and canisterWhat are the down-sides of the Motrag kit? well the gas canister is approx. 10cm diameter in comparison to the 18cm of the Trangia, also the height that the pan sits is 14.5cm in comparison to the Trangia’s 11.5 (lowest) making it more unstable and definitely needing firm level ground to work on. Add to this the fact that the Motrag burner is a small diameter with no support means that pans/kettle have to be placed very carefully or they fall/slide off the side – been there, done that! Finally the lack of a wind shield makes it awkward to use on a windy day – most days in Northern France it seems!

However there is a work around for both issues. Firstly it isn’t rocket science to design (and 3D print) a fold-way set of legs to hold the canister base and increase its stability, secondly a cunningly cut tin-can is used as a slide-down wind shield for the pots and seems to work just fine!

So …. bottom line, will I keep using it?

Yes definitely. For solo trips it suits me down to the ground, it’s compact, clean and neat. The burner is just absolutely awsome – I swear you could spit-roast a whole hog with it! 😀

However when two-up I think the added flexibility of the Trangia just pips it and so it’ll still be my stove of choice for those trips. What I really don’t like about my old Trangia is the residue where the raw aluminium rubs together – however they do a nice hard anodised (27-6HA) version with none-stick pan – luxury! So that’ll be on the shopping list this year I recon! 😀 

A huge thank you goes out to Manuel at Motrag for sending the kit for review – cheers fella!

Motrag radiator guard – UPDATE

Aprilia Caponord ETV1000 Rally-Raid - Northern Italy as day breaks!The Motrag radiator guard has been on the Capo for about 6 weeks/4,600 miles. In that time it has been through driving rain, blazing sunshine and a temperature range of 7C to 35C. Not exhaustive, but a reasonable range of conditions and mileage on which to update the original review.

I don’t know about your Capo, but mine has always had a bit of ‘character’ when it comes to engine-temp versus ambient-temp. Below 25C ambient, the coolant will read a rock-solid 75C day in, day out. But as soon as the ambient temperature begins to rise above 25C, so will the engine-temp. By 35C outdoors, the Capo will run at no lower than 78C AND get hot under the collar when stationary far quicker. Quite understandable and besides, it has done it from day one and never changed – even when the coolant has been!

So how did the guard fare?

  • Quality: Superb! It looks as good now as when fitted. No corrosion or stone damage to the powder coated mesh that I can see.
  • Fit: Adhesive pads are still firmly attached to the radiator after undergoing wide temperature variations and vast amounts of rain!
  • Aprilia Caponord ETV1000 Rally-Raid Motrag radiator guard / protectionAffect on cooling: With ambient temperatures below 30C no noticeable difference in day-to-day running. Above this temp, a slight increase (approx 1-2C) was noticed along with slightly reduced time to fan-on when stationary. However I’m talking a change that was deliberately being looked for and based on years of experience on my Capo ‘as standard’. The fact is the difference is subtle and hardly noticeable at all and most certainly NEVER causes an issue.

Conclusion: This is a quality product at a good price that does the job intended and (to my eye) looks jolly nice as well. Protection, durability and aesthetics for under €70 can’t be bad in my books …. and if your reading this Manuel, bag up another one please for the second Raid! 😀

motrag.com – Radiator guard €64.95 inc. tax

The Artful Bodger

Aprilia Caponord ETV1000 Rally-Raid AMP TE Connectivity Superseal connectotsOK I’ll come clean. I’m a bit of a closet bodger – there I’ve said it. Let’s be fair though, the art of bodging is a skill in itself. A well carried out bodge, with novel and outlandish use of alternative materials to affect a successful repair or upgrade is a beauty to behold. But then again a bad bodge will bite you on the arse quicker than a rabid badger having a rather bad-badger day.

So what did I bodge? Well the LED’s in the Capo’s binnacle might be nice and bright but the wiring behind them certainly wasn’t! Of course a lifetime of working with electric/electronics gives one a certain feel for the bodge to be enacted – why use a decent connector when twisting the wires together and slapping on a bit of insulating tape works just as well …… right?

Aprilia Caponord ETV1000 Rally-Raid AS7, Sparkbright and dashboard autodimming LED's

To be fair it was a temporary solution until I’d got hold of some connectors, except I kept forgetting and one thing led to another … And in the blink of an eye, a couple of years had gone by! Last week however, good old Motrag came to the rescue (again!) with a box full of 2 and 3 way Superseal connectors. I really do like these – 14A rated and waterproof (IP67) compared to the Molex items dotted around the Capo that are 5A and most certainly open to the elements. The only downside is that they are Aprilia Caponord ETV1000 Rally-Raid Motrag Superseal crimp toolmore bulky than the Molex so you can’t cram as many into a tight space!

Of course a cunning and artful bodger could fit these without the correct tool to crimp the connectors, but I yielded to common sense – besides Manuel had put a nifty set of crimping pliers in the box as well! Now all the panels are removable with a mere flick of a locking-tab, no longer do I wish for an extra appendage to assist in separating wires/tape while juggling with the panel. Sheer bliss! Here is a copy of the Superseal installation manual.

To the Mana born

Aprilia Caponord ETV1000 Rally-Raid with Mana indicatorsDeep in the bowels of the Motrag box of goodies are a pair of indicators for an Aprilia Mana – identical body, lens and bulb as used on the Rally-Raid and standard capo 04-onward, but with a greatly reduced stalk length.

Aprilia Caponord ETV1000 Rally-Raid - Mana indicators & Hepco Becker pannier latchWith only very minor modification, these can replace the existing long-stalk indicators on the rear of the Capo, unfortunately they are too short to replace the fronts as well. The mod is so subtle the old indicators can be refitted no problem. When fitted the indicators have much greater clearance from the pannier latches, which makes removal/refitting the pannier easier and they are now well within the width of the pannier rail –  so dropping the bike (not a recommended pastime!) should greatly reduce the chance of a broken rear indicator.

Simply pop off the lens (one screw), prise out the reflector/bulb assembly and disconnect the two wires. Now remove the screw/nut/washer holding the stalk to the mudguard and ease it away while wiggling the wires out. Now the first of two minor modifications are required.

The indicators are held in place by the screw/nut/washer AND a tab that hooks behind the mudguard itself, except on the Mana stalk the tab is too narrow. A quick bit of work with a Dremel soon has that sorted (open gap to approx. 4.5mm). Now the second modification is to extend the slot in the mudguard ( extra 5mm) where the screw passes through. This mod does NOT affect refitting the original indicator as the footprint of the stalk is identical in both cases, so the slot extension is covered by the base of the indicator irrespective of which one is fitted.

Aprilia Caponord ETV1000 Rally-Raid with Mana indicatorsOnce sorted, simply reverse the removal stages – slot in the new stalk and fasten up the screw, nut and washer. Re-thread the two wires back down the stalk and attach to the connectors on the reflector, then screw the lens back in place. Now repeat on the other side, then bask in the warm glow of a job well done, in fact a cold beer goes down a treat about now ….. Ahhhh Mana from Heaven! 😀

NOTE: The indicator bodies are LEFT and RIGHT handed, look at the recess between body and lens – this is the drain and needs to be on the lower edge. I’m not saying I put them on the wrong way round or anything so numpty, perish the thought! 😳

Aprilia Caponord ETV1000 Rally-Raid fitted with Mana indicators

 

Review – Motrag ETV1000 radiator protection

Aprilia Caponord ETV1000 Rally-Raid Motrag radiator protection/guardYesterday a whopping 15Kg parcel of goodies from Manuel at Motrag turned up. Although the box was bursting with new toys, I just focused on the one part I’d really been waiting for – the lovely stainless-steel radiator guard. I know Motrag have had lots of interest in this, which stands to reason with the Touratech guard no longer available. The only other alternative seems to be one from Ebay that could easily be copied for an awful lot less money – after all, it’s only aluminium mesh with a rubber strip and held on by zip-ties.

This guard is made from glass-shot V4A stainless-steel (equivalent SAE316 for harsh environments) with powder coated aluminium mesh bonded to the frame and weighs in at approx 750g. It is held in place by two Scotch ‘Dual Lock’ adhesive fasteners at the top of the radiator and the two fastening points that the ‘cooler spoiler’ (AP8139628) mounts to at the bottom.

Installing the guard is very straight forward …. remove the crash bars & cross brace (if you have them), side panels and spoiler panel. I also removed the tank while servicing the bike which does make access even easier, but isn’t strictly necessary. Give the radiator a good clean and take a few Aprilia Caponord ETV1000 Rally-Raid Motrag radiator protection/guard & fog lamp bracketsminutes to carefully bend back any fins that have been damaged by stones or jay-walking deer. Then clean and thoroughly de-grease the top of the radiator on both sides. The guard has about 1-1.5mm clearance either side when in position – I used a couple of split pins as spacers to make sure the guard was nicely positioned. Do a dry run so you get it located just right and then when you’re happy – whip off the adhesive pad protection and fit the guard for real.

Next up, I had to bond a couple of spacers onto the clips where the spoiler/guard mount –  these take up the space between clip and the new guard. They can’t really be fitted when reassembling the spoiler as access is difficult – hence bonding them onto the clip first. Motrag will be supplying the adhesive in the kit! I gave it 1/2hr to dry, then began the rebuild – crash bar cross-brace, tank, panels, spoiler and finally the crash bars themselves ….. another 20 mins tops.

So, the verdict. Easy to fit with no modifications required. The fit is superb and the stainless frame is nice and stiff, so no worries about vibration induced scuffing of the radiator. As always, the Motrag attention to detail – fasteners and instructions is 100%. If there iAprilia Caponord ETV1000 Rally-Raid Motrag radiator protection/guard & fog lamp bracketss a negative anywhere to be found, then some may question the weight … to me the Capo is a big old lump anyway, a few extra grams won’t snap the frame!

Of course aesthetics are a personal matter, but to me it looks good and is definitely in keeping with the spirit of the Rally-Raid. That just about covers fit and form, but what about function? Well I admit I’ve yet to turn a wheel with the guard in place, but I know Motrag put plenty of miles on a pre-production one and had no problems, so I’m confident it’ll work just fine. But just to be sure, I’ll post again in a few weeks when the Capo has another 3-4K miles on it.

These guards are on sale now over at motrag.com for €64.95 including tax. That’s about half the price of the Touratech guard before it disappeared off the website!

Review – Motrag Garmin 590LM GPS mount

Aprilia Caponord ETV1000 Rally-Raid with Motrag.com base & micro mount for Garmin GPSFor the past six months the eight year old Garmin 2820 has steadily slid its digital cheese off its cracker, forgetting the date and time and generally making a meal of locating satellites. Add to that an annoying habit of swapping screens at random and it’s easy to see why it’s not my best-buddy it once was! Nope …. time for a change.

Which ties in very nicely with Manuel at Motrag.com loaning me a Capo-specific mount for the Garmin 590LM to try out. Unlike the Mad-Maxesque contraptions that Aprilia Caponord ETV1000 Rally-Raid with Motrag.com base & micro mount for Garmin GPSTouratech supply, the Motrag unit is clean and simple …. and pretty uncomplicated. The mount consists of two parts, the ‘Base Mount‘ that bolts to the handlebar clamp (all bolts and spacers supplied) and the ‘Micro Mount’ of choice based on the GPS unit to be fitted. This is attached to the Base Mount via four rubber anti-vibration mounts, again with stainless steel screws supplied.

The 590LM comes with its own bracket for powering the unit and locking it in place, this simply bolts to the Micro Mount which provides the extra support for use in rougher terrain. When the GPS is tucked away in a bag and the ‘Zumo’ cover fitted, the mount is much less in-your-face unlike the Touratech one ……. plus a lot less angular, aggressive and sharp-edged, which is no bad thing.

Aprilia Caponord ETV1000 Rally-Raid with Motrag.com base & micro mount for Garmin GPSFirst impressions are excellent, it holds the GPS perfectly and vibration is virtually none existent, the whole thing is unobtrusive and the powder coating looks like it’ll outlive the Capo. The laser cut ‘Rally-Raid’ is a nice touch and just so no-one feels left out – the mount is available with ‘Caponord’ as well! As always, where possible Manuel supplies stainless steel fasteners that match the look of the OEM Aprilia fasteners – a nice touch. Currently Motrag have Micro Mounts for the Garmin 340/350/390 and 590LM with one in development for the TomTom Rider. Base Mounts are also available for the Multistrada (2012-14) and Hypermotard (2014 on). The cost is €38.95 for the Base Mount and €63.95 for the Micro Mount. The Micro mount in supplied with a plate and clamp so it can also be fitted to a cross-bar or a Ram Mount, in which case you don’t need to buy the Base Mount.GPS-bar-clampAt the time of writing, I’ve done about 450 miles with the mount fitted, some on VERY poor mountain roads and everything is fine. The dashboard is still clearly visible (rider 182cm / 5ft 11inch) and the mount angle goes a long way to limiting screen-glare. I look forward to reviewing the mount along with the Motrag fog-lamp brackets in six months time when the Capo has a good few more miles and a winter under its belt.

Just in the nick of time ……

20150524_131318Just when I’m done-and-dusted, the tools put away and the pannier-packing well underway with only 12hrs before leaving – Manuel’s (Motrag.com) parcel arrives with more goodies for the Capo! I really didn’t think it would be here in time, so I’d planned to fit the box-contents on my return …. but they’re here now so what the hell!

First off, a nice new left-hand lamp bracket and stronger angle-bracket with a funky new fastener – all to mount the GoPro tripod mount base. As usual, beautifully finished and perfect fit. Thanks very much for this Manuel, let’s see what the GoPro makes of it!

Next, one of Motrag’s new GPS mounts for the Rally-Raid. This one is for the Garmin 590LM and can be fitted directly to the supplied bracket or direct to the Accosoto cross-brace where the existing Touratech Garmin 2820 mount sits. Neat and unobtrusive (unlike an empty Touratech mount) it’s functional, yet simple. I’m really looking forward to trying this out (and the 590LM) in the coming weeks as the poor old 2820 has most definitely got a touch of dementia these days – it frequently forgets what day it is, or what country it’s in, bless it! More on this bracket in a later post.

20150508_180804And lastly, the replacement rear sprocket and DID drive chain. A nice slotted-steel sprocket from ‘France Equipement’ in black. I must admit to having never heard of them before, but fit is fine and the finish seems solid enough, so we’ll see what the miles make of it. The ZVM-X (in Gold/Gold) chain is the replacement for the ZVM² that has been on for a staggering 53,400 miles ….. yes one chain, one rear sprocket and three front sprockets for over 53K miles, I’ve never had one last like this before. The only thing negative I can muster against it, is that all the Gold wore off years ago – nowadays it’s just a plain old silver chain!

That’s it for the new stuff but Manuel had one more nugget tucked away in the box for me – a very clean and crack-free pair of inlet rubbers! After reading my post from a few days ago he decided to slip a pair in the box to replenish the MA spares stock – cheers Manuel you are a start indeed!

I’ll end by saying that while some of these items are product testing or favours between friends, I have to make it clear that the chain and sprocket were purchased from Motrag just as anyone else can. The price is extremely competitive and shipping very quick – so next time you’re in need of bits for your bike (not just Caponords), consider having a look at Motrag.com or emailing Manuel to see if a fellow owner/rider/engineer can help you out, I know I’d rather put a few Euro’s his way than in the pocket of some faceless multi-corporation any day of the week.

Review – Motrag Hella DE fog/spot lamp brackets

Aprilia Caponord ETV1000 Rally-Raid - www.motrag.proI’ve known Manuel Hitz, owner of Motrag for over 18 months although we’ve only met once, at ACIM VI in July. At that fun filled weekend we looked around many bikes and discussed the pros and cons of many upgrades – as well as our own. Manuel was keen to show me some of the items that Motrag make and sell, he then asked if I would try a set of his fog/spot light brackets* and compare them to the Touratech ones currently fitted on the RR. ‘Why not’ I said, ‘It would be jolly rude not to!’. And so a parcel arrived last week. 😀

Off with the Touratech brackets ……

Aprilia Caponord ETV1000 Rally-Raid Touratech Fog LampLet’s start with the outgoing Touratech brackets – each has 4 parts, 8 fasteners and weighing approx. 300g. They are actually made for the Mk1 Caponord and not the Mk2, although the modification to fit them is simply a matter of bending the front mounting tab and drilling a fitting point in the fairing. However having to drill out the rear mounting point was something I hadn’t anticipated. The hole was probably a perfect fit for the screw – before they added the powder coating, certainly not after! Overall the fit/finish is average, (presumably) laser cut 4mm aluminium plate bent to shape and slapped with a coat of satin black – sharp edges, cutting marks and even a ding in one plate left for all to see. The lamps sit very close to the fairing making cleaning a real headache unless you remove the brackets each time, on a plus side however; they are well protected in the case of a fall. 4 years on, the finish is peeling away and they have started to look shabby, so I’m glad to have the opportunity to remove them.

Bottom line – Expensive and build quality/finish is average at best.

….. And so on with the Motrag brackets.

Aprilia Caponord ETV1000 Rally-Raid Motrag fog light brackets with Hella DE lampsThe Motrag brackets each have 3 parts, 6 fasteners (plus a plastic pin) and weigh in at approx. 360g**.
Opening the box was a pleasure. Each bracket wrapped securely, fasteners (all stainless steel and just like the OEM Aprila fasteners in appearance) were bagged and labelled for their intended location and last but not least a set of clear instructions and a parts list.

Fitting the brackets involved no drilling or cutting at all and they were on and aligned in less than 30 minutes – ok, the lamps were already wired in of course! In comparison to the Touratech brackets, the lamps sit slightly wider apart (approx. 25%) and slightly higher with adequate clearance for me to get behind them when cleaning the bike. The flat top of the lamp bracket lends itself very nicely to being used as a mount for my GoPro camera, something Manuel is keen for me to try out – so keen if fact, he sent three lamp brackets – a spare for me to drill for the camera mount!

OK so far … a bracket’s a bracket, heck as long as it fits and doesn’t look naff what else can I say? Well let’s save the best for last, the finish, THIS is Motrag’s ace-in-the-hole! Each bracket is exquisite, no sharp edges, no machine or cutting marks in sight. This kind of attention to detail is something we’re just not used to seeing nowadays and it pays dividends …..As the old saying goes:

Don’t spoil the ship for a ha’p’orth of tar

Proverb: Don’t risk the failure of a large project by trying to economize on trivial things.

Says it all really! And so to the bottom line – Excellent fit and finish, well documented instructions and nice attention to detail with the fasteners adding that OEM look. But you know I’ve been thinking, wouldn’t it be nice to either tweak the design, or offer a seperate bracket so that a pair of discreet DRL – Daytime Running Lights could be fitted in the space below the lamp … over to you Manuel! 😉 

Anyway, that’s about if for the initial impressions, I’ll add a new post in 2015 when I’ve had chance to bounce the brackets up and down our road and put them through winter weather to see how the finish holds up – my guess is they’ll do fine. That just leaves me to thank Manuel for kindly sending the brackets for review, we agreed it was to be fair and without bias, if I didn’t like something – say it! All good so far …….

I almost forgot – Manuel also dropped another little present in the box for me, a sexy new cap for the coolant bottle in blackest black, not sun-bleached grey. That little baby has got to be worth an extra 5mph! 😉 AP8104124 if you want to do this speed enhancing upgrade.

Aprilia Caponord ETV1000 Rally-Raid. New coolant cap!


Notes

*Both the Touratech and Motrag brackets are designed to take the Hella DE spot(Xenon) or fog(Halogen) lamps. Motrag supply the lamps/brackets as individual sets for the left or right, so you can mix fog/spot combinations as you want.

**These are a prototype set in 2.5mm steel and not the production 3mm aluminium, so they are slightly heavier.